So easiest ways how to fix rear window washer. Lets see them one by one. From the windshield, windshield wipers help remove dirt. For this reason, you may be wondering how to add post-cleaning fluid. Fortunately, it’s not difficult. Why? Because there is no separate tank. One reservoir for all windshield washers. Worker filling windshield wiper fluid
It’s the little thing we worry about when we buy a car. Those who have never owned an afterwasher might think there is a separate reservoir for after wash fluid. So replaces like 2016 lincoln mkx wiper blade replacement cost more money you always need pay attention to you wipers.
You probably know that your main fuel tank is located under the hood of your car. This same liquid will satisfy all your windshield cleaning needs. It’s in the front and back. Keep this in mind if you frequently spray both the front and back as it will run out sooner than if you had no chance. Remove the bolts. Locate the windshield washer fluid reservoir. So Remove the bolts that secure the windshield washer reservoir to the fender or body.
How to fix rear window washer – Remove the windshield washer pump connection
If the washer pump is equipped with a harness connector, remove the connector. If the wash pump does not have a harness connector, use wire cutters to cut the wires. Also you can use subaru windshield washer fluid like fluids for any vehicle without any consequences.
Notice: Do you know that wiper blades like 2014 camry wiper blade size are nw rare to find.
Remove the windshield washer fluid hose from the reservoir.
If there are clips, you will need to use needle nose pliers to remove the clips and wire.
Remove the windshield washer reservoir from the vehicle.
Remove the wash pump from the tank.
Install the new pump.
Now Install a new flush pump in the flush tank.
Install the water tank.
So Install the windshield washer reservoir on the fender or body in the engine compartment.
Connect the wiring harness to the wash pump.
If the wires must be cut, you will need to strip the harness and wires from the pump with wire strippers. Insert the two butt connectors with heat shrink and press the wires into the butt connectors.
Install the windshield washer fluid line into the reservoir.
If you remove the tie, you will need to use needle nose pliers to install the tie and thread. Fill with cleaning fluid. Pour liquid into reservoir and fill. If the wash is concentrated, you will need to mix the wash with distilled water following the directions on the bottle.
Inspect the car.
Put the ignition in the auxiliary or working position. Operate the wash pump switch or lever. Make sure no fluid is leaking from the windshield washer nozzle.
Install the 9 volt battery into the cigarette lighter.
This will allow your computer to work and save the current settings to the car. If you don’t have a 9-volt economizer, you can replace it without it. It’s easier.
Disconnect the battery.
Open the hood of the car. Turn off the ignition system and windshield wipers and remove the ground cable from the negative battery terminal. It is important to protect your hands. Always wear protective gloves before removing battery terminals.
Remove the windshield washer pump located along the wing in the upper part of the engine compartment
Remove the tank mounting bolts.
Locate the windshield washer fluid reservoir. Remove the bolts that secure the windshield washer reservoir to the fender or body.
Remove the plug from the harness.
Now Remove the wiring harness connector installed on the windshield washer pump.
Remove the windshield washer fluid hose from the reservoir.
If there are clips, you will need to use needle nose pliers to remove the clips and wire. Remove the windshield for further doing and also the receiver as well. Remove the wash pump from the tank.
How to fix rear window washer – Clean the contacts.
Clean the contacts on the harness connector and the contacts on the wash pump. Remove the windshield washer pump located in the wheel arches or in the lower fender under the vehicle Loosen the clamping nut.Use a pry bar or ratchet to loosen the lug nuts on the tire and wheel to be removed. Make sure to leave the lug nuts on the wheel studs. Lift the car. Using the jack recommended for the weight of the vehicle, lift the vehicle at the indicated jack point until the wheels are completely off the ground.
Remove the windshield washer fluid hose from the reservoir. If there are clips, you will need to use needle nose pliers to remove the clips and wire. Remove the windshield for further doing and also the receiver as well. Remove the wash pump from the tank. Clean the contacts. Clean the contacts on the harness connector and the contacts on the wash pump. Remove the windshield washer pump located in the wheel arches or in the lower fender under the vehicle
Loosen the clamping nut.
Use a pry bar or ratchet to loosen the lug nuts on the tire and wheel to be removed. Make sure to leave the lug nuts on the wheel studs. Lift the car. Using the jack recommended for the weight of the vehicle, lift the vehicle at the indicated jack point until the wheels are completely off the ground.Install the bracket. The jack bracket should be located under the jack. Then lower the car onto the jack. On most modern vehicles, the jacking point is located in the weldment under the door at the bottom of the vehicle. Remove the tires and wheels from the fender arches you are working on.
You may need to remove the inner fenders to gain access to the windshield washer reservoir and pump. So Remove the screws. Remove the bolts that secure the windshield washer reservoir to the fender or body. Remove the plug from the harness. So Remove the wiring harness connector installed on the windshield washer pump.
So Remove the washer fluid hose from the reservoir. If there are clips, you will need to use needle nose pliers to remove the clips and wire. Remove the windshield for further doing and also the receiver as well. Remove the wash pump from the tank. Clean the contacts. Clean the contacts on the harness connector and the contacts on the wash pump.
So now you know how to fix rear window washer. I hope that this article helped you with your cause. See you soon.